9 answers
Do you have access behind the radiator or is it stuck against the wall? The easiest thing is to use a hair dryer on cool setting or a vacuum with a flat nozzle to blow the dust out, running it carefully between the tubes. If it's really caked on, an old toothbrush dipped in warm water helps you loosen the dirt without having to take anything apart.
A hair dryer works fine, but honestly a vacuum with blow mode is way more powerful! I'd say the best option is to use one of those compressed air canisters you can get anywhere - it blasts the dust out in a way you wouldn't even believe. If you don't have one handy, a hair dryer on cold or even a powerful fan pointing from the opposite side works great. The key thing is to aim from bottom to top so the dust falls out of the radiator instead of just swirling around inside it.
Try sticking a cloth or gauze between the radiator fins and then run the vacuum over it - the cloth catches the fine dust that would otherwise escape and keeps it from flying around the room! If the radiator has a lot of dust buildup, a soft brush (like a toothbrush) also works well for loosening the dirt before vacuuming, it saves you time and leaves it cleaner.
The first thing not to do is stick a brush or anything abrasive directly between the fins, because you'll end up bending them and ruining the radiator's thermal efficiency. Don't use water either, since it gets trapped in there and causes you trouble with humidity and rust.
Compressed air works well, but if you don't have a compressor handy, the best option is to combine two things: first run the vacuum in suction mode but without touching it - just hold the nozzle a few centimeters away so it sucks up the dust that comes loose. Then, with a damp cloth (not wet, just damp) pressed against your finger, run it along the outer grooves of the radiator from top to bottom; the cloth catches the fine dust floating in the air and keeps it from spreading all over the room. It's slower than blowing, but it works pretty well if the dust is stuck on.
If the radiator is completely unreachable from behind or from one side, another trick is to put a flat cardboard box underneath to catch everything that falls while you use the vacuum from above. That way the dust doesn't scatter across the floor and you get it all clean in a moment.
Compressed air and a vacuum do work, but they create a mess with dust floating all over the place. What worked best for me is to barely dampen an old rag with water and run it between the fins while you have the vacuum on suction mode on the other side: the dust sticks to the wet rag instead of flying everywhere, and you end up with everything cleaner and without trashing the room.
Canned compressed air is your best bet here - way more controlled than a compressor and you don't need to set anything up. Give it short bursts from different angles so the dust comes out without getting stuck in the fins, and if it's really dirty, combine that with a dry cloth run gently between the lamellae before you blow, but don't press hard. Skip the water and stiff brushes like people said before - that's just asking for trouble with the radiator.
How's the access to your radiator - is it in a corner or do you have it pretty clear? I've had good results just using an old paint brush, carefully running it between the fins while blowing the dust downward as I go, then vacuuming up what falls. The compressed air people mention works great if you have one handy, but honestly a soft brush and patience will do the trick without spending anything. The key is not to press hard - just let the brush glide and let gravity do the work.
If the radiator is in a corner or against the wall, a soft-bristled brush (the kind used for cleaning bottles) lets you get between the fins without bending them, and then you run the vacuum over it to pick up what comes loose. It works pretty well if there isn't too much dust.
One thing that works well is doing a quick pass with a soft brush or a brush with very soft bristles, but only if the fins are in good condition and aren't too fragile. The idea is to brush lightly so the dust falls without forcing anything. Then, once you've loosened the bulk of it, you can run the vacuum over it calmly or use a slightly damp cloth to catch what's left.
What works especially well if the radiator is wedged between a wall and a sofa (which is pretty typical) is using a narrow cardboard or plastic tube that you attach to the vacuum's nozzle to reach the deep corners between the fins. It lets you be more precise than with the flat nozzle and gets to spots where other methods leave dust behind.
Your answer
Log into answer.